brianwatch47
User Name: You need to be a registered (and logged in) user to view username.
Total Articles : 0
https://www.thekeylab.co.uk/peugeot-car-keys/
Peugeot 208 Key Replacement It is better to leave the replacement of Peugeot 208 keys to auto locksmiths equipped with the right equipment and skills They can design and program keys more quickly and at a lower cost than dealerships If your key fob stopped locking or unlocking your doors it is likely due to a dead coin battery There are also other reasons that the key could be malfunctioning Dead Coin Battery A dead battery can stop your Peugeot 208 from locking and unlocking as well as hindering it from starting the engine If this is the case youll have to use the backup starting method that is detailed in the owners manual of your vehicle The spark plugs can also be worn out The KeyLab are responsible for sparking the fuel that starts the engine They have a limited life span Theyll eventually fail if theyre not used enough There is a straightforward solution to this issue The best solution is to determine the voltage of your car battery using a multimeter If the voltage is below 115 volts then its time to replace it If the battery has corroded it is important to clean its contacts You can do this by lifting the rubber covers that protect both battery terminals and using wire brushes to clean any parts that are corroded from the battery Then reconnect the positive and negative pole cables Water Damage If your 208 wont start and the battery hasnt been replaced you must look at the spark plugs It could be that they are just overly dirty which causes them not to spark The spark plugs can be cleaned in an workshop Peugeot automobiles use a key with a transponder that is compatible with the immobiliser This guarantees that only the right key can start the engine If the chip inside the Peugeot key is damaged it will not transmit the proper signal to the vehicle Water damage is a common reason for this issue This is most common in colder climates where the vehicle could have been exposed to snow or rain If this is the case you should call a reputable auto locksmith who has all the tools and equipment needed to change the keys programming Theyll also have the latest technology and equipment needed to make a Peugeot smart key The process should take no more than 15 minutes Contacts of the battery may be damaged Peugeot changed from the old carbonencased transponder chips to an entirely new kind of chip that utilizes electronic components that are placed on circuit boards The new system is great when its new however the circuit boards wear out over time and stop working properly This can prevent the immobiliser chip from working which means that your car wont start Contact a Peugeot specialist or a locksmith if this is the case Another issue that is common is when the key fob battery gets depleted which causes the key blade to stop from entering the lock A locksmith for cars will replace the battery and then cut a new blade for you This is a quick solution Faulty Receiver Module If your Peugeot key fob stopped working after dropping it on the floor getting exposed to a sudden downpour or accidentally washing it it could be due to a malfunctioning receiver module The receiver module is responsible for transmitting radio frequencies to the onboard computer that controls the central locking system of your Peugeot vehicle Rubber seals on the key fob block water from getting to the electronic chip Water can damage the chip in the event that it is exposed water for a prolonged period of time The high salt content of the pool or ocean water can cause damage to the key fob especially if it is submerged If your Peugeot spare key fob isnt working it is necessary to have the module replaced This can only be done by an expert auto locksmith or Peugeot specialist As opposed to other cars Peugeot keys are protected by an unique immobilizer system that requires the correct coding in order to start the engine It is for this reason that you should only rely on the Peugeot locksmith to design and program a replacement Faulty onBoard computer The onboard computer in your Peugeot is responsible for a variety of systems in your car including airbags and power windows The onboard computer will show a code if something goes wrong This code will be stored within the system until the issue is fixed Usually this will mean replacing the onboard computer The most common reason for the airbag warning light to turn on is corrosion or loose connections in the sensor This can be caused by wear and tear aging or exposure to moisture and salt This issue needs to be addressed as soon you can since an airbag that is malfunctioning could pose a risk in the event of an accident If you encounter the error card not found on your Peugeot key fob the battery in the key fob could be weak or dead This can prevent the key fob from sending a signal that disables your vehicles immobilizer You can test this by pressing the unlock button on the key fob and then trying to start your vehicle If it doesnt work it is because the battery of the key needs to be replaced
