cementblack96
User Name: You need to be a registered (and logged in) user to view username.
Total Articles : 0
https://www.repairmywindowsanddoors.co.uk/stockport-windowrepair/
Replacing uPVC Window Handles It is simple to change the handles on upvc windows The important thing is to ensure that the new handle is a good fit for the spindle that was cut out of the window mechanism If you follow the steps below any cockspur handle can fit on most windows The most important factor is the step height of the handle What to look for As time passes uPVC handles on many windows in the UK can start to show signs wear and wear and tear The window handle can become loose or difficulttooperate when this occurs This is a relatively easy task that can be completed by anyone who is familiar with basic hand tools The first step is to ensure that the handle is firmly connected to the window frame and is in a position that is open The next step is to locate the screws or pins which hold the handle They are usually on the inside of the handle They can be removed using a screwdriver and pliers When the handle has become loose and sagging gently pull it back from its hinges Then you will need to locate a new handle that is the same size and style This can be done online or in an area DIY store and should take five minutes using an screwdriver The most important thing to consider when replacing a uPVC window handle is the step height This is the distance from the bottom of the handle to the point at which it sits on the window frame It is generally a standard measurement and it is essential that you check the step height of your current handle before purchasing an entirely new one There are various sizes depending on the kind of handle repairmywindowsanddoors can be found for uPVC windows with lug centres of 31mm while cockspur handles have lug centres of 43mm Tilt and turn handles are typically found on uPVC windows and they have a special design that allows the window to be slid up for ventilation and turned to open the window fully The most common cause of breakage in uPVC handles is that they crack inside instead of breaking away from the base section This makes them difficult to open and is why it is crucial to ensure that any replacement handle you purchase has the same spindle length as the one you have Take off the handle from the old one If the handles on your windows are damaged or improperly fitted they could cause doubleglazed windows to close and open incorrectly They may even get stuck This could be due to a number of factors such as general wear and tear on the handle or corrosion In these cases it is crucial to replace the upvc window handle as promptly as you can to prevent further damage or loss of function When replacing the handles of windows made of upvc you should remove the old handles from the window To do this start by taking off the screw that is encased when the handle is in its closed position This will reveal a screw and once it is removed you are able to begin to remove the handle itself It is possible to make the task easier by using an electronic screwdriver You should also be aware that screws can be hidden beneath plastic caps It is recommended to remove the covers with the help of a Stanley knife After you have removed the old handle you will be required to inspect the square cutout on the base to make sure that the new handle you choose for the window lock is compatible This is important because youll need to determine the length of the spindle on the previous handle to ensure it is the same size as the window mechanism and handle spindle cut out The different kinds of window handles made from upvc include Espag handles which are equipped with a central screw and can turn left or right Cranked handles which have two screws and are used on tilt and turn windows made of upvc as well as Spade handles which have a flat arm and can be used on either side of the window It is easy to replace the handle after you have found one that is suitable Simply put it in place and ensure that the spindle is correctly inserted into the lock mechanism Once you have done this you can tighten the handle onto the window frame The replacement upvc handle will now be secure Measure the Spindle If youre replacing a upvc window handle that has slipped off its because the spindle holding it in place has become damaged or loose In certain situations it is possible to tighten the spindle using pin or screw In some instances it might be necessary to replace the handle There are a few different types of upvc window handles These include inline espagnolette handles cockspur handles and tilt and turn handles Each type of handle is installed and replaced in a different way Before you purchase a new handle its important to know the dimensions of the handle that is currently in use This will ensure that the new handle is the right size and fits into the window All handles are sized in accordance with industry standards making it easy to determine the right size To measure the handles size move the window to the open position You should be able to see the size of the screw or pin that secures the handle Use a ruler or a tape measure to determine how long the spindle is Once you know the length of the spindle you can buy a new one with exactly the same size The step height of a window handle is another factor to take into consideration when buying replacements The step height is the distance from the base of the handle to the point at which it sits on the frame It is typically around 21mm or 9mm in aluminum and uPVC Dropping something into the gap will let you see how far the handle extends before it comes into contact with an obstruction Cockspur handles may have different backsets depending on what style of window you install them in Inline the espag handle heights range from 43mm from the centre to the centre two fixing points Cockspur handles however have different backset heights according to the style of the window they are in This is due to the fact that they have a spur that extends from their handle and is locked onto a cockspur wedge striking plate Install the New Handle After you have chosen the new handle align it carefully with the screw holes on the door Then secure it using the screws provided Install the latch lever in the same manner as the handle that you are replacing when youre replacing the door handle Then you can reattach the door trim to hide the mounting screws and finish off your project Tip To remove a metal head from a wedge made of wood place the handle on the floor so that its wide end is level with the ground Then use an hammer and tap the thin end Be careful not to damage the handle or the spindle
