expertdibble3
User Name: You need to be a registered (and logged in) user to view username.
Total Articles : 0
https://www.repairmywindowsanddoors.co.uk/acton-windowrepair/
Replacing uPVC Window Handles It is simple to change the handles on upvc windows It is important to ensure that the new handle is a good fit for the spindle carved out in the window mechanism If the steps below are followed properly any cockspur handle should be able to fit into most windows The key is the step in the height of the handle What to Look For Over time uPVC handles on many windows in the UK may begin to show signs wear and wear and tear The window handle may become shaky or difficult to operate when this occurs This is a simple job that can be accomplished by anyone who is comfortable using basic hand tools The first thing to do is make sure that the handle is securely fixed to the window frame and is in an open position The next step is to find the screws or pins that secure the handle They are usually on the inside of the handle They can be removed using an screwdriver or pliers Once the handle is loose it can be taken from its hinges by gently pulling off It is then necessary to find a replacement handle of the same style and size This can be done on the internet or in a local DIY store and it should take about five minutes with the help of a screwdriver One crucial aspect to take into consideration when replacing the uPVC window handle is the step height This is the distance between the handles base and where it is located in the frame of the window This is a standard measurement and you should check the height of the step prior to ordering a replacement handle There are various sizes depending on the type of handle Inline handles for uPVC windows generally feature lug centers of 31mm and there are also cockspur handle types with 43mm centres Tilt and turn handles are often found on uPVC windows and they have a special design that allows the window to be tilted in for ventilation and turned to open the window fully The most common uPVC handle cracks are internal instead of a break at the base This can make it difficult to open It is crucial to ensure that the replacement handle has the same spindle that was used in your original one Remove the Old Handle If the handles on your windows are damaged or improperly installed they could cause doubleglazed windows to not open or close correctly They could even become stuck There are a variety of reasons for this such as general wear and tear or corrosion of the handle made of metal In these instances it is crucial to replace the upvc window handle as soon as you can to prevent further damage or loss of functionality When replacing the handles of windows made of upvc it is recommended to remove the handles that were previously installed from the window Start by removing the screw covered with the handle when it is in a closed position This should reveal another screw and once removed you are able to begin to take off the handle itself You can make the job easier by using an electronic screwdriver It is also worth noting that the screws on the handle could be hidden behind plastic caps therefore it is a good idea to take the Stanley knife to the screws and remove them Once the old handle is removed you must examine the square cut on the handles base to ensure that the new window lock handles will work with it It is crucial to measure the spindle length on the handle that was used and compare it to the size of the window mechanism spindle cutout There are three kinds of Upvc handles Espag handles with a central screw that can be turned either left or right and Cranked handles with two screws and Spade handles which have flat arms and can be used either side of the upvc window Once you have a suitable replacement it is simply a case of screwing the handle into place and making sure that the spindle is correctly inserted into the lock mechanism After you have done this tighten the handle to the window frame Your replacement upvc handles will now be secure Take a measurement of the Spindle If you have to replace a handle made of upvc that has fallen its likely that the spindle holding it in place is damaged or is loose In some instances this could be fixed with pins or screws to secure it In other cases it will need to be replaced entirely There are a few different types of upvc window handles There are three kinds of handles inline espagnolette tiltandturn and cockspur Each type has a different method for installing and removing the handle It is essential to measure the handle before buying a replacement This will ensure that the new handle is of the correct size and fits into the window Luckily all handles conform to industry standards for sizing so its fairly easy to find the right size To determine the size of your handle first remove it from the window by turning it to the open position upvc replacement door handles will then be able to determine the size of the screw or pin that is holding it Use a ruler or tape measure to determine the length the spindle is Once you have determined the length of the spindle you can purchase a replacement one that is exactly the same size When purchasing a replacement window handle it is crucial to be aware of the step height of the upvc window handle The step height is the distance from the bottom of the handle to the point at which it is placed on the frame Typically this is about 21mm for uPVC windows and 9mm for aluminum To ensure that the new handle is suitable it you can drop something in the gap to check how far it goes before it comes into contact with an obstruction Cockspur handles come with different backsets depending on what kind of window you want to install them in Inline espag handle heights are 43mm from centre to center two fixing points Cockspur handles however have different backset heights depending on the shape of the window they are in This is because they have an extension spur that extends from the handle and is secured over a cockspur wedge striker Fit the New Handle Once youve selected the new handle align it carefully with the screw holes on the door Then secure it using the screws supplied If youre replacing the latch lever it can be installed similarly to the main door handle Then attach the door trim again to hide the screws for mounting Tip To remove the head made of metal from the wooden wedge make sure the handle is held so that its broad end rests on the floor Then use a hammer to tap the thin end of the handle Be careful not damage the handle or the spindle
