hoodtemple1
User Name: You need to be a registered (and logged in) user to view username.
Total Articles : 0
https://www.repairmywindowsanddoors.co.uk/cambridge-windowrepair/
Door Hinge Repair Cambridge The hinges on your doors are a small but vital element that can make a significant difference in the look and functionality of your doors Replacing noisy hinges can be a quick inexpensive upgrade to improve the curb appeal of your home One common way to repair door hinges that sound squeaky is to use bar soap or petroleum jelly Rub the soap or petroleum jelly on the hinges to cover it Replacement Hinges If theyre worn out or damaged hinges can cause major damage The good news is that hinges are simple to replace and dont require any special tools It is essential to select the proper hinge for your home This will ensure that your door shuts and opens easily If your hinges for your door arent working properly call an expert as soon as you can to fix them A faulty door hinge can result in the door becoming warped or pulled from the frames base This is typically caused by poor use or weight too much To avoid this from happening it is important to lubricate your hinges This will stop the hinge from rusting or squeaking and will extend the life of your doors There are a few different types of hinges and each one comes with its own advantages and drawbacks The most common hinge is the butt joint which is secured to the door using pins on each side This kind hinge is suitable for use on doors with light frames as it doesnt need much strength to open and shut However the butt joint is more susceptible to deterioration than other hinges It is recommended to make use of continuous piano hinges for heavy doors wooden windows and doors cambridge wwwrepairmywindowsanddoorscouk of door hinge runs across the entire length of the door It allows the door to be shut and opened easily The advantage of this type of hinge is that it doesnt need center support and is more sturdy than other hinges Another common type of hinge is the storefront door pivot hinge which allows doors to pivot from one location at the top and the bottom of the door They are commonly found in commercial locations and are difficult to repair if damaged Professionals can assist you in installing a new pivot or replacing the old one The cost of hinges will vary depending on the kind Loose Hinges When hinges are loose they will cause the door to hang in a crooked manner and may even start to scrape against the floor which is irritating at the very least The loose hinges are a frequent issue that can be fixed by anyone with a few basic tools Often simply tightening the hinge screws will do the trick but in some cases the screw holes might have become stripped and wont remain tight If the holes in the screws have been stripped youll need to bore the holes and plug them with wooden dowels or glue coated matches made of wood It is essential to lubricate and tighten your door hinges frequently to avoid them becoming loose It is also essential to look for signs of damage to the hinges If you notice any cracks or chips on the metal it could be time to replace the hinge It is also recommended to replace hinges if they begin to bind or stick when you open and shut the door The most common cause of hinges on doors becoming loose is wear and tear due to frequent use and not having proper tightening or lubrication This is particularly true for doors that are used frequently by children because they can hang from the handles of the door or swing the door on the hinges This puts an unnecessary strain on the hinges This can result in them becoming loose and eventually falling off completely If the hinges are loose for a short amount of time you can simply tighten them using a screwdriver but when theyre loose for a longer time the constant movement of the hinge plate as well as the screws will eventually enlarge the holes that the screws enter This eventually makes it impossible for the screws to stay tight and theyll be ripped rendering them useless To remedy this take the bare end of the match with a wooden one in regular carpenter glue and tap it lightly with the hammer This will push the glue as deep into the hole as possible You may need to use a number matches that are coated with glue to fill in the hole Rusty Hinges Rust can cause problems with hinges for doors This is particularly true for older doors It can make hinges appear ugly but it can also cause them to fail and break This could pose an issue for those who use the door Fortunately its possible to save a damaged hinge with a little work The first step is to remove the hinges and cleaning them to remove any gunk After the hinges have been cleaned they can be oiled and used again In days gone by hinges that were of low quality were made of iron and steel which would often get rusty however modern doors are often made with brass or metal alloys that dont rust as easily However some people still rely on the oldfashioned iron hinges because of their beauty and durability even though theyre more susceptible to rust than modern hinges The best way to avoid this is by preventing the hinge from rusting in first place It is the easiest way to clean the hinges regularly using steel wool and water especially when they are damp If you do it regularly rust will not be a problem for your hinges for doors If youre looking to take things further consider using hinges made of stainless steel Unlike iron stainless steel will not be rusty and will give your home modern look If you cant replace your existing hinges the best thing to do is to periodically scrub them and then grease them When youre removing the hinges its best to do so fully to get into all the little places to wash off any corrosion Once the hinges are clean you can use an oilbased mixture with vinegar to further lubricate them and aid in helping them stay protected against corrosion This is a cheap and easy solution that can be easily found in the majority of homes and is worth a shot before you consider replacing your hinges Doors that wont shut In time doors become misaligned due to the expansion and contraction of wooden frames When this occurs the door could get caught on the edges of the frame or get caught on the latch when trying to shut it A little bit of work can often fix these issues If you are able to tighten the hinges and fix the alignment issue then your door will close correctly again Begin by looking over the hinges to find any loose screws A loose screw can cause the hinge leaf to slide creating a gap between it and the jamb This can cause the latch not to reach the strike plate hole and cause a jammedup door To fix this remove one of the hinge screws and slide a piece of cardboard we prefer using the backs of old legal pads between the hinge and the door jamb Then screw the hinge back into its place This will widen the gap on the hinges side and narrow it down on the latch side which allows the latch to be free of the strike plate If this solves the issue you can repeat the procedure for the remaining hinges If youre still having trouble then you could hammer or shim the strike plate to align it with the hole in the latch If this is the case a some paint and wood filler is often enough to hide these changes Damage to the physical structure or prolonged use can also cause the strikeplate to be bent or warped and cause it to touch the edge and not extend far enough into the hole to keep the door shut To test for this apply lipstick to the latch and then stick a strip of masking tape onto the strike plate Close the door and then open it The lipstick will leave an impression on the tape at the point where the latch is able to meet the strike plate hole If the mark is below the hole then the latch should be moved up
