paintgun9

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.repairmywindowsanddoors.co.uk/croydon-windowrepair/

Replacing uPVC Window Handles The replacement of window handles made of upvc is a simple job The most important thing is to ensure that the new handle is a good fit for the spindle cut out in the window mechanism If the steps listed below are followed the cockspur handle will fit most windows The height of the step of the handle is key What to Look For A large portion of windows in the UK come with uPVC handles Over time they may begin to show signs of wear and tear The handle on the window can become loose or difficulttooperate when this happens This is a simple job that can be accomplished by anyone who is comfortable with basic hand tools The first step is to make sure that the handle is securely fixed to the frame of the window in its open position The next step is to locate the pins or screws that hold the handle They are usually on the inside of the handle They can be removed using an screwdriver or pliers When the handle is loose It is best to gently pull it away from its hinges It is then time to find a new handle of the same style and size This can be done online or at a local DIY store and should take around five minutes using a screwdriver When replacing a uPVC handle It is crucial to think about the step height This is the distance from the base of the handle to where it sits on the window frame This is a standard measurement and you should verify the height of the step before purchasing a replacement handle Depending on the kind of handle you choose there are different sizes available Inline handles can be found for uPVC windows with centers of 31mm for lugs while cockspur handles have lug centres of 43mm Tilt and turn handles are typically used on windows made of uPVC and they come with a unique design that allows the window to be slid up for ventilation and then rotated to fully open the window The most common uPVC handle cracks are internal rather than a fracture from the base This can make them hard to open and it is therefore essential to ensure that any replacement handle you buy has the same length of spindle as the one you have Remove the old Handle A poorly installed or damaged window handles could cause your doubleglazed windows to open or close improperly and could even cause them to become stuck This could be due to various factors including general wear and tear on the metal handle or corrosion In these instances it is essential to replace the window handle as quickly as you can in order to prevent further damage or loss of function One of the first steps that you should do when replacing the handles on your windows made of upvc is to remove the old handle from the window To do this start by taking off the screw that is encased when the handle is in the closed position Once you have removed that screw you are able to remove the handle It is a good idea to employ an electric screwdriver to accomplish this as it will make the task much easier and quicker Be aware that screws can be hidden beneath caps made of plastic It is best to remove the covers with a Stanley knife After the old handle has been removed take a look at the square cut out at the base of the handle to ensure that the new window lock handles are compatible with it It is essential to measure the length of the spindle on the handle that was used and then compare it with the dimensions of the window mechanism spindle cutout The various types of window handles made from upvc include Espag handles which feature a central screw that can be turned left or right Cranked handles which have two screws and are used on tilt and turn upvc windows as well as Spade handles with an arm that is flat and can be put on either side of the window It is easy to replace the handle after youve located one that is suitable Just screw it into place and ensure that the spindle is inserted correctly in the lock mechanism Once you have done this then tighten the handle to the window frame The replacement upvc handle should now be secured Measure the Spindle If youre replacing a upvc window handle that has slipped off its likely because the spindle that holds it in place has become damaged or loose In some instances this could be fixed using pins or screws to secure it In certain situations it might be necessary to replace the handle There are several different types of handles made from upvc There are three types of handles inline espagnolette cockspur and tiltandturn Each type of handle is installed and replaced in a different way Before purchasing a replacement handle it is essential to know the dimensions of the handle that is currently in use This will ensure that the handle fits the window in a proper manner and will be the right size All handles are calibrated in accordance with industry standards making it easy to find the correct size To measure the size of your handle first remove it from the window by turning it back to the open position You will then be able to see the size of the screw or pin that secures it Then use a tape measure or ruler to determine the length of the spindle Once repairmywindowsanddoors have determined the length of the spindle you can purchase a new spindle that is exactly the same size When purchasing a replacement window handle it is crucial to be aware of the step height of an upvc window handle The step height is the distance from the bottom of the handle until where it rests on the frame Typically this is around 21mm for uPVC windows and 9mm for aluminum Dropping something into the gap will allow you to determine how far the handle extends before it meets an obstruction Cockspur handles often have different backset heights based on the type of window they are placed in Inline espag handles have an average height of 43mm from centre to centre 2 fixing points Cockspur handles however have different backset heights according to the shape of the window theyre in This is because they have a spur which extends from their handle and locks onto a cockspur wedgestriking plate Install the new handle When youve chosen a new handle carefully align it with the screw holes in the door and secure it with the screws supplied If youre also replacing the latch lever it can be put in the same way as the main door handle Finally reattach the door trim in order to conceal the screws for mounting and finish the project Tips To remove a metal head from a wooden wedge place the handle on the floor so that its wide end is on the floor Then use a hammer and tap the narrow end Be careful not to damage the handle or the spindle